Difference between revisions of "Nuvoton"

From ElectroDragon
Jump to: navigation, search
 
(20 intermediate revisions by the same user not shown)
Line 1: Line 1:
 +
[https://github.com/Edragon/Nuvoton Github all resources link.]
 +
== Datasheet ==
 
* [[File:DS_N76E003_EN_Rev0.04.pdf]]
 
* [[File:DS_N76E003_EN_Rev0.04.pdf]]
 
* [[File:DS_N76E003_SC_Rev0.04.pdf]]
 
* [[File:DS_N76E003_SC_Rev0.04.pdf]]
  
 +
== Toolchain ==
 +
* [[: File:Keil_Driver.zip | keil driver ]]
 +
* [[: File:BSP.zip | Demo code BSP]]
 +
<gallery>
 +
File:Nuvoton setup 02.gif | Animation setup
 +
File:Nuvoton_serial_upload_02.gif | Upload bootloader by Nulink and use serial upload, animation
 +
File:2018-04-12 114949.png | Connect pins 3.3V, CLK, DA, RST, GND to board, should only use 3.3V for n76e003, auto detect IC.
 +
File:2018-04-21_010227.png | Post process job for hex2bin
 +
</gallery>
 +
* Post-process job, run hex2bin to convert hex to bin for serial download
 +
C:\Users\Administrator\Desktop\N76E003串口下载工具\hex2bin\hex2bin.exe .\Output\GPIO.hex
 +
=== Serial Download Note ===
 +
* Need run hex2bin to convert bin file, MCU only support BIN download
 +
* Please use above post build method for bin file when compile.
 +
* need reset/repower MCU before and after flash.
 +
 +
== Specification ==
 +
* 1T / 8051: 1T Value Microcontroller, 8051 We are more familiar with the classic kernel;
 +
* 18KB Flash ROM: better than 8KB Flash, and 18KB of flash space, all can be used as data storage space;
 +
* Same 1024B SRAM
 +
* 17 + 1 inputs: better than up to 16 GPIOs;
 +
* 2xUART, I2C, SPI: Better than SPI / I2C / UART (one more UART);
 +
* 8ch of 12bit ADC: better than 5ch 10bit ADC;
 +
* 6ch of individual duty PWM: better than 3 PWM outputs;
 +
* 10KHz LIRC for WDT reset / WKT;
 +
* 16MHz HIRC ± 1% Room temp. ± 2% full condition;
 +
* -40 to 105 ℃ wider temperature range;
 +
* 2.4V to 5.5V wider supply voltage range;
 +
* TSSOP20 / QFN20;
 +
* ESD & EFT: HBM / 8KV MM / 400V, Over 4KV, excellent ESD and EFT, immunity to interference and ESD protection;
 +
 +
[[File:Ne76e003 spec.png|700px]]
 +
 +
== Schematic ==
 +
* Full schematic tiny board - [[File:NuTiny-SDK-N76E003_V1.0.pdf]]
 +
* Development Board Manual - [[File:UM_NuTiny-SDK-N76E003_EN_Rev1.00.pdf]]
 +
* Below schematic, crystal part should be wrong, nuvoton n76e003 use powered crystal.
 +
<gallery>
 +
File:2018-02-12_235823.png | minimum schematic
 +
</gallery>
 
[[category: Topics]]
 
[[category: Topics]]

Latest revision as of 08:12, 10 May 2018

Github all resources link.

Datasheet

Toolchain

  • Post-process job, run hex2bin to convert hex to bin for serial download
C:\Users\Administrator\Desktop\N76E003串口下载工具\hex2bin\hex2bin.exe .\Output\GPIO.hex

Serial Download Note

  • Need run hex2bin to convert bin file, MCU only support BIN download
  • Please use above post build method for bin file when compile.
  • need reset/repower MCU before and after flash.

Specification

  • 1T / 8051: 1T Value Microcontroller, 8051 We are more familiar with the classic kernel;
  • 18KB Flash ROM: better than 8KB Flash, and 18KB of flash space, all can be used as data storage space;
  • Same 1024B SRAM
  • 17 + 1 inputs: better than up to 16 GPIOs;
  • 2xUART, I2C, SPI: Better than SPI / I2C / UART (one more UART);
  • 8ch of 12bit ADC: better than 5ch 10bit ADC;
  • 6ch of individual duty PWM: better than 3 PWM outputs;
  • 10KHz LIRC for WDT reset / WKT;
  • 16MHz HIRC ± 1% Room temp. ± 2% full condition;
  • -40 to 105 ℃ wider temperature range;
  • 2.4V to 5.5V wider supply voltage range;
  • TSSOP20 / QFN20;
  • ESD & EFT: HBM / 8KV MM / 400V, Over 4KV, excellent ESD and EFT, immunity to interference and ESD protection;

Ne76e003 spec.png

Schematic